
When my friend Tif asked if I could make a hoodie for her son, I jumped at the chance. Sure, I’ve never tried to mimic an anime character before, but I’m always up for a challenge.
To get started, I did a Google search for “mudkip” and checked out the links to some mudkip hoodies Tif and her son had found online (I can’t find the original links or I’d share them with y’all). Bulbapedia had some good information, as well as drawings to help me figure out some of the essentials for sewing the hoodie.
I decided to use Burda 7916 as the basis for the hoodie and substitute fleece for the jersey. It worked OK but the fleece does have less give to it than jersey, so it can be a little bit of a struggle to get the hoodie on and off. If I had to do it over again, I’d size up.
I made a contrasting “racing stripe” for the middle by making a new cut line 2.25″ over from the fold line on the front piece. The new “side front pieces” are cut 2″ over from the original fold line (creating a 1/4″ seam allowance). If I had to do it over again, I think I’d make more of a contrasting belly panel about 8″ wide.
The biggest modifications I made to the hoodie were adding a contrasting lining from a pink knit and the fins/gills. You can download the pattern pieces I made here. (Requires Adobe Acrobat Reader or another PDF viewing program.) Note that the back fin piece is on two pages (connect at the dashed line) and that the head fin needs a 1/4″ seam allowance added around the top and sides (but not the bottom edge).
Cut two of the hood pieces from pink knit for the lining.
Cut two of the back fin pieces from light blue fleece and two from fusible fleece.
Cut two head fin pieces from royal blue fleece and two from fusible fleece.
Cut four gill star pieces from orange fleece and four from fusible fleece*.
Cut two 6″ circles from orange fleece.
Cut out two back shirt pieces but not on the fold. Instead, add 1/4″ to the center, which allows you to add the back fin to the rear of the shirt by sewing it into the seam.
I made each of the fin/gill pieces by fusing the fleece to the wrong side, then sewing the pieces right sides together with a 1/4″ seam allowance. (Note: I did most of the sewing on my serger — much faster and easier that way. If you don’t have a serger, follow the pattern instructions for using a twin needle on your sewing machine. I used a single needle and longer stitch length on the gills to preserve the points of the stars, though.)
Turn the fin and gill pieces right side out and press. I used black thread and a long stitch length on my sewing machine to add detail stitching on the fins (the stitch lines are marked on the pattern pieces).
Pin the back fin piece to one back shirt piece about 4″ up from the bottom edge of the shirt. Match the other back shirt piece so that the fin is sandwiched between them and sew with a 1/4″ seam allowance.
Attach the head fin between the two royal blue fleece hood pieces and sew with a 1/4″ seam allowance.
Position the orange circles on either side of the hood and stitch down. I used a long stitch length and sewed around the edge but you could stitch them down by hand or use a machine blanket stitch instead.
Tuck the unsewn edges of the orange gill pieces inside each opening, then hand stitch to the center of each circle. I used a double length of thread and stitched the length twice to make sure the gill was really tacked down.
Sew the pink knit hood pieces together, then match the hood and hood lining, right sides together, and sew along the front edge with a 1/4″ seam allowance. Turn right side out and press. I used a hand needle and thread to secure the seam of the hood lining to the seam of the hood to keep the lining from sagging.
Follow the rest of the pattern instructions to complete the hoodie, then wear and be the envy of all your friends!
* I inadvertently used fusible Peltex inside the gills instead of fusible fleece. So, while the gills are nice and stiff, turning them right side out was haaaaaateeeeefullllll.